By purchasing the purchaser attests that they possess the necessary training and authorization to properly use this product. The purchaser assumes all liability for events arising from the use of this product and will not hold Mission Spec civilly or criminally liable.
This promo video (below) was produced for the standard sized EC2 plate carrier.
- Ultra-light weight.
- Full PALS grid on front and rear plate bag for attachment of MOLLE compatible pouches and gear.
- Ready for integration of industry standard chest rigs (QASM buckels needed).
- Rear plate bag can be independently raised to properly fit user (see video).
- Spacer mesh for moisture wicking, improved airflow, and heat dissipation.
- Removable/adjustable MOLLE compatible side straps (see video).
- Dual front Tourniquet holders.
- Dual front pen or chemlight pockets.
- ITW Nexus IR Signature Reduction buckles (excluding black).
Intent of the EC2-XL
Just as its predecessor the EC2-XL was designed to accept up to level IV body armor, offer a full PALS grid, and with three individuals in mind: Law Enforcement for either low-viz use or active shooter response where level III or IV armor is needed. Military Special Operations where weight savings here can allow for other equipment. The Civilian who understands he or she is ultimately responsible for their own safety and wants every advantage possible.
- Mission Spec ShoulderSavers™ mk3.
- Mission Spec FlankSavers™.
- Mission Spec MagRack5™ chest rig.
- Haley Strategic Partners D3CR products.
- Chest rigs/panels that conform to industry standard specs.
- This is not a comprehensive list.
Rear Plate Bag Height Adjustment
The Mission Spec EC2-XL has the ability to raise the rear plate bag in order to properly fit more individual users. This is accomplished by changing where the (included) four side straps anchor to the front and rear plate bag (see video). Your EC2-XL should arrive with the side straps attached to the top two available positions on the front plate bag and the bottom two available positions on the rear plate bag. This causes the rear plate bag to ride about 1.5-2″ higher than most other plate carriers. If you would like to configure your EC2 to have both plates ride at the same height you will need to manipulate the connection points of the four side straps. All four of the side squeeze (female) buckles are of the split-bar design (see picture or video). That is to say they can be removed and reattached to different anchor points on the plate bags. The ladderloc attachment on the rear plate bag are also of the split-bar design and can also be moved.
- 500D CORDURA®.
- 29 ounces.
- Fits XL (e,x)SAPI armor plates or 11×14″ Shooters Cut plates.
- Berry Compliant (see: Berry Amendment USC, Title 10, Section 2533a).
- 100% U.S.A Designed, Tested and Manufactured.
- Limited Lifetime Warranty
Improvements from original EOC-XL
- +1 vertical inch of loop Velcro on front plate bag for ID patches.
- Added vertical PALS and loop Velcro to bottom 3 PALS rows for chest rig integration.
- Added dual tourniquet holders to front plate bag. Can also be used for coms cable routing.
- Added dual pen/chemlight holders on front plate bag.
- Eliminated front triglide buckles on shoulder straps.
- Added elastic properties to side straps.
- Added simulated PALS sewn into side straps for MOLLE pouch support.
- Reduced weight from airmesh by removing unnecessary portions.
- Added extra PALS row on rear plate bag to support more third-party packs.
- Added ‘Pack Hangers’ to rear plate bag for integration of future Mission Spec products.
- Added elastic bands to plate bag sides for comms cables and hydration tube routing.
Armor is not included with this product.
Designed to fit a XL (11″x14″) Shooters Cut or (e,x)SAPI cut plates.
Q: Will the EC2-XL fit AR500 brand armor?
A: Yes, as long as it is not rectangular and is ~11×14″. AR500 armor is usually much thinner than a SAPI plate so there will be some extra space in the plate bag. However, with the EC2 plate suspension your armor should still always stay in the highest most position in the platebag and should not move around when being worn.
Q: Will the EC2-XL accept a chest rig attachment?
A: Yes, industry chest rigs that follow the standard “micro buckle pattern” should integrate with the EC2-XL’s front facing loop Velcro field and the vertical PALS channels.
Q: Is the EC2 a fully US produced product with US sourced components?
Q: Can I use my mk2 ShoulderSavers™ with the EC2-XL?
A: Yes, they are fully compatible if you don’t want to purchase the newer mk3 ShoulderSavers™.
Q: Why does the EC2-XL have two side straps on each side?
A: Two side straps offers extra security (redundancy). Two side straps interface better with more chest rigs and chest panels. Two side straps will better stabilize any side mounted MOLLE pouches. If you need none of this, feel free to remove 2 of the side straps.